Marine & heavy · ISO 8217 RME 180, trade fuel oil 180 cSt. 2017 edition limits shown; check the edition in your contract
Fuel oil 180 CST (RME 180)
Heavy fuel oil with a viscosity up to 180 cSt at 50 °C. A lighter, easier-to-handle grade used by industry, smaller power plants and ships.
- 11Parameters
- 11With a limit
- 11Off-spec causes explained
- Flash pointmin 60 °C
- Densitymax 991 kg/m³
- Viscositymax 180 mm²/s
- Cold flowmax 30 °C
- Sulphurmax 3.5 % m/m


Image credits Laboratory glass samples are made from reference photos on Wikimedia Commons by Chemik10 (CC BY-SA 2.5) and a CC0 petroleum sample photo.
Stir the liquid to feel how thick it is
Move the mouse or a finger across the liquid. Press and drag to stir harder. Keyboard: arrow keys stir, Space shakes.
Very thick Very heavy. It barely moves and flows back slowly.
Typical viscosity from the dataViscosity at 50 °C: max 180 mm²/s
- Stir speed
- 0 px/s
- Liquid movement
- 0%
- Settled after
- -
- Surface
- Still
The class is a guide for feel. The viscosity figure shown is the one in the specification data.
How it looks
Black and opaque, a little less thick than 380 cSt. Judge quality by the certificate and independent samples, not by eye.
Where it is used
- Industrial boilers and kilns
- Small power plants
- Marine fuel for slower ships
Handling and safety
- Heated tanks and lines.
- Independent inspection with sealed samples at both ends.
- Check the sulphur limit against the destination's rules.
Typical properties
- Viscosity at 50 °C
- max 180 mm²/s
- Density at 15 °C
- max 991 kg/m³
- Sulphur
- max 3.5 % m/m
- Flash point
- min 60 °C
- Pour point (summer)
- max 30 °C
- Carbon residue
- max 15 % m/m
- Ash
- max 0.07 % m/m
- Water
- max 0.5 % vol
The specification
ISO 8217 RME 180, trade fuel oil 180 cSt. 2017 edition limits shown; check the edition in your contract. Limits are the commonly published ones. Your contract and the current edition of the standard decide.
| Parameter | Limit | Test method | What it protects |
|---|---|---|---|
| Viscosity at 50 °C | max 180 mm²/s | ISO 3104 / ASTM D445 | Pumping, heating and atomising. |
| Density at 15 °C | max 991 kg/m³ | ISO 3675 / ASTM D4052 | Purification and energy content. |
| Sulphur | max 3.5 % m/m | ISO 8754 / ASTM D4294 | Emissions. Use the contract limit. |
| Flash point | min 60 °C | ISO 2719 | Fire safety. |
| Pour point (summer) | max 30 °C | ISO 3016 | Handling in the cold. |
| Carbon residue | max 15 % m/m | ISO 10370 | Combustion quality. |
| Ash | max 0.07 % m/m | ISO 6245 | Wear and deposits. |
| Water | max 0.5 % vol | ISO 3733 | Sludge and corrosion. |
| Vanadium | max 150 mg/kg | ISO 14597 / IP 501 | High-temperature corrosion. |
| Aluminium plus silicon | max 50 mg/kg | ISO 10478 / IP 501 | Abrasive catalyst fines. |
| Total sediment, potential | max 0.1 % m/m | ISO 10307-2 | Stability. |
Why a cargo goes off spec
When one parameter fails, it usually points to one cause. Here is what to look for.
Viscosity at 50 °Cmax 180 mm²/s
Too highHeavy cut.
Why it mattersPumping, heating and atomising.
Density at 15 °Cmax 991 kg/m³
Too highAromatic residue.
Why it mattersPurification and energy content.
Sulphurmax 3.5 % m/m
Too highSour residue.
Why it mattersEmissions. Use the contract limit.
Flash pointmin 60 °C
Too lowLight ends or contamination.
Why it mattersFire safety.
Pour point (summer)max 30 °C
Too highWaxy residue.
Why it mattersHandling in the cold.
Carbon residuemax 15 % m/m
Too highHeavy residue.
Why it mattersCombustion quality.
Ashmax 0.07 % m/m
Too highSalt or fines.
Why it mattersWear and deposits.
Watermax 0.5 % vol
Too highTank water.
Why it mattersSludge and corrosion.
Vanadiummax 150 mg/kg
Too highHeavy crude origin.
Why it mattersHigh-temperature corrosion.
Aluminium plus siliconmax 50 mg/kg
Too highCatalyst fines.
Why it mattersAbrasive catalyst fines.
Total sediment, potentialmax 0.1 % m/m
Too highUnstable blend.
Why it mattersStability.
Check your own certificate
Type the values, paste the certificate text, or upload a PDF or photo. The checker names every parameter that is off spec and the usual reason.
| Parameter | Limit | Your value | Result |
|---|---|---|---|
| Viscosity at 50 °CISO 3104 / ASTM D445 | max 180 mm²/s | enter a value | |
| Density at 15 °CISO 3675 / ASTM D4052 | max 991 kg/m³ | enter a value | |
| SulphurISO 8754 / ASTM D4294 | max 3.5 % m/m | enter a value | |
| Flash pointISO 2719 | min 60 °C | enter a value | |
| Pour point (summer)ISO 3016 | max 30 °C | enter a value | |
| Carbon residueISO 10370 | max 15 % m/m | enter a value | |
| AshISO 6245 | max 0.07 % m/m | enter a value | |
| WaterISO 3733 | max 0.5 % vol | enter a value | |
| VanadiumISO 14597 / IP 501 | max 150 mg/kg | enter a value | |
| Aluminium plus siliconISO 10478 / IP 501 | max 50 mg/kg | enter a value | |
| Total sediment, potentialISO 10307-2 | max 0.1 % m/m | enter a value |
Sources
- ISO 8217:2017 Petroleum products, fuels (class F), specifications of marine fuels
- ASTM International, petroleum standards
Indicative information for professional users. Not a substitute for the standard, a contract or an independent inspector.