Skip to content

Middle distillates · ASTM D975 Grade No. 2-D S500 and trade gasoil

Gasoil 500 ppm

General purpose diesel with sulphur up to 500 ppm. It is traded for road, rail, generators and industry in markets that have not moved to 10 ppm.

Request Gasoil 500 ppm
  • 12Parameters
  • 11With a limit
  • 12Off-spec causes explained
  • Flash pointmin 52 °C
  • Density820 to 860 kg/m³
  • Viscosity1.9 to 4.1 mm²/s
  • Cold flowreport °C
  • Sulphurmax 500 ppm (mg/kg)
  • Boiling end282 to 338 °C
Typical colour, laboratory glass
Laboratory glass sample of Gasoil 500 ppm, in its typical colour
A sample of Gasoil 500 ppm in laboratory glass on a dark studio background, so the colour is easy to judge.
Reference photograph
How Gasoil 500 ppm is stored and moved in practice.

Image credits Laboratory glass samples are made from reference photos on Wikimedia Commons by Chemik10 (CC BY-SA 2.5) and a CC0 petroleum sample photo.

Stir the liquid to feel how thick it is

Move the mouse or a finger across the liquid. Press and drag to stir harder. Keyboard: arrow keys stir, Space shakes.

Thin
Colour follows the typical colour of Gasoil 500 ppm.
Thin and looseThick and heavy

Thin Light and free flowing. Waves travel quickly and fade slowly.

Typical viscosity from the dataViscosity at 40 °C: 1.9 to 4.1 mm²/s

Stir speed
0 px/s
Liquid movement
0%
Settled after
-
Surface
Still

The class is a guide for feel. The viscosity figure shown is the one in the specification data.

How it looks

Clear and bright, pale yellow to light amber. A slight dark tint is normal at the top of the range. Haze means water, and a dark or brown fuel means contamination, oxidation or a heavy cut. Some markets dye diesel red for off-road or tax reasons.

Where it is used

  • Road and rail diesel
  • Generators and industrial burners
  • Blending stock for bunkers

Handling and safety

  • Keep tanks free of water. Drain bottoms regularly.
  • Check a retained sample against the certificate at discharge.
  • Add lubricity or cetane additive where the contract requires.

Typical properties

Sulphur
max 500 ppm (mg/kg)
Flash point
min 52 °C
Distillation T90
282 to 338 °C
Cetane number
min 40
Viscosity at 40 °C
1.9 to 4.1 mm²/s
Water and sediment
max 0.05 % vol
Ash
max 0.01 % m/m
Carbon residue on 10% bottoms
max 0.35 % m/m

The specification

ASTM D975 Grade No. 2-D S500 and trade gasoil. Limits are the commonly published ones. Your contract and the current edition of the standard decide.

ParameterLimitTest methodWhat it protects
Sulphurmax 500 ppm (mg/kg)ASTM D2622 / D5453Emissions, and the poisoning of exhaust catalysts.
Flash pointmin 52 °CASTM D93 (PMCC)Fire safety in storage and transport.
Distillation T90282 to 338 °CASTM D86Controls combustion quality, smoke and deposits.
Cetane numbermin 40 ASTM D613How easily the fuel ignites in a diesel engine.
Viscosity at 40 °C1.9 to 4.1 mm²/sASTM D445Pump and injector lubrication and spray.
Water and sedimentmax 0.05 % volASTM D2709Clean fuel: water causes rust and bacterial growth.
Ashmax 0.01 % m/mASTM D482Abrasive solids in the engine.
Carbon residue on 10% bottomsmax 0.35 % m/mASTM D524Tendency to leave deposits.
Copper strip corrosionmax 3 classASTM D130Corrosive sulphur compounds.
Lubricity, HFRR wear scarmax 520 µmASTM D6079Low-sulphur fuels can lose the natural lubricity that protects pumps.
Density at 15 °C820 to 860 kg/m³ASTM D4052Energy per litre and a check on the cut.
Cloud pointreport °CASTM D2500Wax appears below this temperature and can block filters.

Why a cargo goes off spec

When one parameter fails, it usually points to one cause. Here is what to look for.

Sulphurmax 500 ppm (mg/kg)

Too highCut from sour crude or poorly hydrotreated stream, or contamination with a higher-sulphur product.

Why it mattersEmissions, and the poisoning of exhaust catalysts.

Flash pointmin 52 °C

Too lowGasoline or naphtha contamination, a light cut.

Why it mattersFire safety in storage and transport.

Distillation T90282 to 338 °C

Too highA heavy cut, fuel oil or vacuum gasoil carry-over.

Too lowA light cut.

Why it mattersControls combustion quality, smoke and deposits.

Cetane numbermin 40

Too lowAromatic or cracked components, or no cetane improver.

Why it mattersHow easily the fuel ignites in a diesel engine.

Viscosity at 40 °C1.9 to 4.1 mm²/s

Too highA heavy cut.

Too lowA light cut or kerosene blend.

Why it mattersPump and injector lubrication and spray.

Water and sedimentmax 0.05 % vol

Too highTank bottoms, leaking roofs, condensation, poor settling.

Why it mattersClean fuel: water causes rust and bacterial growth.

Ashmax 0.01 % m/m

Too highContamination with residual fuel or dirt.

Why it mattersAbrasive solids in the engine.

Carbon residue on 10% bottomsmax 0.35 % m/m

Too highA heavy cut or cracked components.

Why it mattersTendency to leave deposits.

Copper strip corrosionmax 3 class

Too highActive sulphur or contamination.

Why it mattersCorrosive sulphur compounds.

Lubricity, HFRR wear scarmax 520 µm

Too highHeavily hydrotreated fuel with no lubricity additive.

Why it mattersLow-sulphur fuels can lose the natural lubricity that protects pumps.

Density at 15 °C820 to 860 kg/m³

Too highA heavy cut or residual fuel contamination.

Too lowA light cut.

Why it mattersEnergy per litre and a check on the cut.

Cloud pointreport °C

Too highWaxy crude or a heavy cut in a cold market.

Why it mattersWax appears below this temperature and can block filters.

Check your own certificate

Type the values, paste the certificate text, or upload a PDF or photo. The checker names every parameter that is off spec and the usual reason.

or paste the certificate text
ParameterLimitYour valueResult
SulphurASTM D2622 / D5453max 500 ppm (mg/kg)enter a value
Flash pointASTM D93 (PMCC)min 52 °Center a value
Distillation T90ASTM D86282 to 338 °Center a value
Cetane numberASTM D613min 40 enter a value
Viscosity at 40 °CASTM D4451.9 to 4.1 mm²/senter a value
Water and sedimentASTM D2709max 0.05 % volenter a value
AshASTM D482max 0.01 % m/menter a value
Carbon residue on 10% bottomsASTM D524max 0.35 % m/menter a value
Copper strip corrosionASTM D130max 3 classenter a value
Lubricity, HFRR wear scarASTM D6079max 520 µmenter a value
Density at 15 °CASTM D4052820 to 860 kg/m³enter a value
Cloud pointASTM D2500report °Center a value

Sources

Indicative information for professional users. Not a substitute for the standard, a contract or an independent inspector.