Passare al contenuto

Heavy fuels

Cutter Stock

Cutter stock is a lighter oil blended into heavy residue to reduce its viscosity. Typical cutters are gasoil, kerosene or light cycle oil.

← Tutti i prodottiDetto anche: Cutter, Cutterstock, Cutting oil (fuel oil), Viscosity cutter

  • Densità800 to 950 kg/m³
  • Viscosità1 to 30 mm2/s at 40 C
  • Intervallo di ebollizione170 to 400 °C
  • PericoloDepends on the cutter (for example UN1202 for gasoil), Depends on the cutter; Class 3 if gasoil or kerosene
Colore tipico, vetro da laboratorio
Campione in vetro da laboratorio di Cutter Stock, nel suo colore tipico
Un campione di Cutter Stock in vetro da laboratorio su sfondo scuro da studio, per valutare facilmente il colore.
Scala dei colori
I colori che Cutter Stock può presentare.

Crediti delle immagini I campioni in vetro da laboratorio sono realizzati da foto di riferimento su Wikimedia Commons di Chemik10 (CC BY-SA 2.5) e una foto di un campione di petrolio CC0.

Agitate il liquido per sentire quanto è denso

Muovete il mouse o un dito sul liquido. Premete e trascinate per agitare più forte. Tastiera: le frecce agitano, Spazio scuote.

Medio
Il colore segue il colore tipico di Cutter Stock.
Fluido e scorrevoleDenso e pesante

Medio Oleoso. Le onde sono più lente e più arrotondate.

Viscosità tipica dai dati1 to 30 mm2/s at 40 C

Velocità di agitazione
0 px/s
Movimento del liquido
0%
Si calma dopo
-
Superficie
Fermo

La classe è solo una guida alla sensazione. Il valore di viscosità mostrato è quello dei dati di specifica.

Aspetto

Clear to dark

Dove si usa

  • Fuel oil blending
  • Bitumen cutback

Manipolazione e sicurezza

  • Store in heated tanks, typically 40 to 50 C for pumping and 100 to 150 C for centrifuge and injection, with the temperature kept at least 10 C above the pour point and below 20 C under flash point. Avoid overheating that causes coking. Check for incompatibility when mixing batches (ASTM D4740 spot test or D7060). Sampling follows ISO 3170 or ISO 3171 with MARPOL retained sample. Inspect for water, catalytic fines (aluminium plus silicon) and total sediment.
  • Flammable if gasoil or kerosene.

Proprietà tipiche

Aspetto
Clear to dark
Densità a 15 °C
800 to 950 kg/m³
Intervallo di ebollizione
170 to 400 °C
Viscosità
1 to 30 mm2/s at 40 C
Punto di scorrimento
Varies
Zolfo tipico
Varies

◉What it is

Cutter stock is any lighter petroleum stream used to dilute a heavy oil so it flows and meets a viscosity target. In fuel oil blending, it brings vacuum residue down to 180 or 380 mm2/s. Common cutters are gasoil, light cycle oil, kerosene, visbreaker gasoil and diesel. The cost, sulphur and density of the cutter directly affect the blend. Fuel oil blending is a major business at storage hubs.

⬡What it is made of

C10 to C25 distillate or cracked stock.

⚛La chimica

Light aromatic and paraffinic hydrocarbons act as solvent for asphaltenes. Too much paraffinic cutter can destabilise asphaltenes.

⚙How it is made

Taken from distillation or cracking units.

▶How it works

Blending uses a viscosity blending index to calculate how much cutter is needed.

▣Storage, loading and inspection

Store in heated tanks, typically 40 to 50 C for pumping and 100 to 150 C for centrifuge and injection, with the temperature kept at least 10 C above the pour point and below 20 C under flash point. Avoid overheating that causes coking. Check for incompatibility when mixing batches (ASTM D4740 spot test or D7060). Sampling follows ISO 3170 or ISO 3171 with MARPOL retained sample. Inspect for water, catalytic fines (aluminium plus silicon) and total sediment.

★Why it matters in the Gulf

Blenders in Fujairah use distillate cutter, typically gasoil or light cycle oil, to make bunker fuel. Specific blending volumes are not stated.

Molecole chiave

Norme e specifiche

ISO 8217The finished blend must meet the marine fuel specification.
ASTM D341Viscosity-temperature charts for liquid petroleum products.

Pericoli

Depends on the cutter (for example UN1202 for gasoil)Classe Depends on the cutter; Class 3 if gasoil or kerosene

Flammable if gasoil or kerosene.

Come si commercializza

Units

Metric tonnes

Benchmarks

Priced from gasoil or LCO

Typical cargo

Barge or tanker

Incoterms

FOB

Notes

Cost tied to gasoil.

Raffinerie che lo producono: i nostri suggerimenti

91 raffinerie censite producono questo prodotto, 21 delle quali nel Golfo, in Iran e in Iraq. Diamo la precedenza agli impianti del Golfo, poi a quelli in esercizio, poi a quelli per capacità.

Vedere tutti i 91 sulla mappa

Terminal che lo movimentano

Lo sapeva?

💡 Cutter stock cost can account for a large part of bunker blend price.

💡 Incompatible cutters can create sludge.

Si metta alla prova su Cutter Stock

Domanda 1 di 3 · Punteggio 0 · Serie 0

What does cutter do?

Altro in questo gruppo

Fonti

Redatto con parole proprie di PST a partire dalle fonti sopra. Affidabilità dei dati: medium. I valori tipici variano in base all'origine e al contratto, quindi legga sempre la specifica nel Suo contratto.